Pulnix TS-9720EN Series Instalační manuál stáhnout pdf (Strana 32)

Page 20

VIS CAM 300/400 Installation Manual

Installing the Vehicle Imaging System

FIGURE 18. Properly wired X-4 connector.

8. The cable is mounted in the cable entry on the back side of the camera as shown in the Figure 19

below. The rubber bushing is mounted around the jacket and the metal brace is mounted around the

shield securing proper electrical connection from the shield to the metal housing (se figure

Figure 19).

FIGURE 19. Back of the video camera.

For a detailed description of the VIS CAM 300/400 interface please refer to See “ Appendix A: Camera

Functional and Connector Description” on page 43 in this manual:.

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 115 116

Vehicle Imaging 1
Subsystem 300/400 1
Warranty 3
Certifications 3
WARNING 4
Table of Contents 5
Page vii 7
Page viii 8
List of Figures 9
List of Tables 11
Page xii 12
1 Introduction 13
FIGURE 1. VIS elements 14
1.3.2 VISCAM 15
1.3.3 Illumination 16
1.3.4 VJP-300 Junction Panel 16
1.3.5 RS485 Device Server 16
1.4 Operational Overview 17
2 Preparing for installation 18
Preparing for installation 21
1. Disconnect Power 27
3.2 Installing the Camera(s) 29
3.3 Installing the J-Panel 33
FIGURE 24. Test trigger 38
3.4 Illumination Options 40
1 2 3 4 5 6 40
1 2 3 4 5 6 7 8 42
4 System Set-Up 43
5.1 I/O Board Layout 56
5.2.1 Functionality 57
FIGURE 40. Interface drawing 58
5.2.6 Typical wiring diagram 61
5.3.1 Functionality 62
FIGURE 46. Switch location 63
TABLE 12. Wiring diagram 63
5.3.5 Typical Wiring Diagram 64
5.3.7 Functionality 65
FIGURE 53. Connecting to a 2 68
FIGURE 56. Detection board 70
5.5.1 Functionality 71
TABLE 14. Connector table 72
5.6.1 Functionality 73
5.6.5 Test setup 1 75
5.6.6 Test setup 2 76
5.7.1 Functionality 77
5.8 Cables 78
6.1 J-Panel Layout 79
Description 81
6.2.5 Typical Wiring diagram 82
6.2.6 Indicators 83
6.2.7 Switches 83
6.3.1 Functionality 84
6.3.2 Connector specification 84
TABLE 20. Signal table 85
6.3.5 Typical Wiring diagram 86
6.3.6 Indicators 87
6.3.7 Switches 87
6.4.1 Functionality 88
6.4.5 Indicators 89
6.7 X6, X7: 24V DC Power 92
FIGURE 76. RS485 to Ethernet 94
6.11 X14: External Trigger 97
FIGURE 81. Trigger 0 98
FIGURE 82. Trigger 1 98
TABLE 32. Connector table 98
6.12.1 Functionality 99
Master to slave connections 103
FIGURE 86. Terminal block 104
Page 100 112
Page 101 113
Page 102 114
www.jai.com 116

Komentáře k této Příručce

Žádné komentáře

Pulnix TS-9720EN Series Instalační manuál Strana 32

Komentáře k této Příručce

Související produkty a manuály pro Bridge kamery Pulnix TS-9720EN Series